HDMI Vertical single twisting machine:
1. Type: Vertical wire twisting
2. Application: Adopt guide wheel device,two core wire+1 ground wire twist
3. Power: 2HP AC motor + 2 HP converter
4. Rotating velocity: 1000RPM/max, constant speed
5. Method of traverse: Adopt cross tooth traverse
6. Winding tension: Adopt magnetic powder brake+ knob control tension size
7. Two aluminum foil frame, because is fixed vertical single twisting machine two side: Adopt magnetic powder brake + knob control tension size
HDMI power feed wire frame:
1. Type: Two-head + one-head, shaftless + two high-frequency spark tester detection
2. Wire spool size: 400mm
3. Power: 0.5HP AC motor + converter
4. Tension adjustment: Slider + auxiliary adjustable
5. Upper and lower shaft type: Manual type
6. Rotate speed: Angle detection cooperate mainframe speed automatic adjustment

 

Technical parameter and performance introduction
Application	Suitable for PE, PVC core wire and copper wire twisting and side change taping
Take-up bobbin	Standard ABS bobbin：Outer diameterφ400xinner width300xOuter width265xOuter holeφ56mm
Two lay length scope	20mm-96mmOR8.5mm-40mm
Rotate speed	1000rpm/min
Motor power	Three-phase 380V 1.1Kw frequency conversion speed regulation
Brake	5kg single plate electromagnetic brake
Meter count	Five-digit opto-electronic meter count
Take-up tension	Magnetic powder clutch
Packing	Single-layer or double-layer
Machine size (mm)
weight

High-speed automatic twisting machine

 

Model	YK-φ500B
Max rotate speed	3000rev/min(6000twist/min)
Twisting	Suitable for above seven strand of the silver jacketed wire, tinned wire, enamelled wire, bare copper wire, copper-clad steel, copper cladding aluminum
Feed wire diameter	φ0.08-φ0.45mm
Twisting area	0.035-2.5mm2
Lay length	40 sections 6.3-50.4mm
Twist direction	Left and right can freely selected
Take-up bobbin	Standard ABS bobbin：Outer diameterφ500xOuter width300xinner width250xinner holeφ56mm
Polish rod traverse	φ20mm
Center height of main shaft	700mm
Method of main shaft lubrication	Oil lubricating, natural circulation cooling
Brake	NSK Adopt Japan original enter port brand NSK Electromagnetic brake
Bearing	Electromagnetic brake, B type inside the brake by magnetic powder clutch automatic adjustment
Take-up tension	Use 2.5kg Magnetic clutch
Protection	Inner and outer broken-wire automatic brake, meter count arrived will automatic shut-down
Safety protection	All the doors can be opened, and lifting no place can not start or automatic braking
Instruction	Machine state, have corresponding fault should indicator instructions
Control	By PLC + converter control
Noise figure	About 80db
Main motor power	5.5KW
Machine size (mm)	(L)2780×(W)1280×(H)1260
weight

φ50+35mm foaming skin extrusion production line

 

Model	YK-50+35mm
Pay-off type	Active single shaft tension pay-off
Pay-off wire spool	PN400-500mm
Screw diameter	φ50mm
Screw L/D ratio	25:1
Extrusion output	70kg/h
Main motor power	15HP
Wire diameter specification	0.6-4.0mm
Temperature control	5Segment
Cooling device	Folding type W model/U model
Capstan power	3HP
Accumulator type	Inclined/horizontal
Accumulate length	250m
Outlet wire speed	MAX500m/min
Take-up type	Double shaft bundle install/shaft install
Take-up spool	PN400-500mm
Electric control	Controlled inverter+PLC entire joumey control(may choose the use)
Installation external dimension
Total weight

φ630mmHigh speed rotate frame single twisting machine

 

Model	YK-φ630mm
Feed wire shaft size	φ400mm-φ500mm-φ630mm
Winding shaft size	Outer diameterφ630xOuter width475xinner width415xinner holeφ56mm
Application wire diameter	φ0.6mm-3.0mm
Max twisting outer diameter	φ15mm
Lay length	20-200mm
Rotate speed	1000rpm
Take-up tension	Pneumatic tension freely adjusts
Method of traverse	According to the wire bobbin self and moving stepless speed regulation
Traverse pitch	2mm-12mm
Twist direction	Left and right can freely selected
Taping method	Center lapping or side packing
Upper and lower wire bobbin	Hydraulic lifting
Machine size (mm)
weight

Numerical control type single layer/double layers wrapping machine

Uses widely: Suitable for stranded wire, double layer/single continuous center wrapping.
High output: High speed rotation, work rate in 2.5 times than traditional taping machine.
Tension is steady: The taping tension automatic calculation and trace, keep the constant tension from start to end, need not to manual adjustment.
Pitch accurate: Controlled by PLC, the pitch more accurate.
Good traversing: Take-up traversing used in shift traversing, the pitch could order by yourself.
High quality: Production the HDMI, DP, TA, SATA and SAS etc,rate of pass 100%

 

Type	YK-500mm Numerical control type single layer/doublelayers wrapping machine
Purpose	It’s used to twisted wire,parallel wire double layer/single layer continuously center wrapping
Core specification	AWG32-AWG20
Taping materail	Aluminum foil tape,cotton paper tape,transparent tape,mica tape,teflon tape
Rotation speed	MAX2000rpm/MAX28m/min
Power	Adjust the speed by 1HP motor drievers,taping drum and directs motor linkage
Taping tension	Taping tension keep constant from begin to end
Take-up tension	Take-up tension keep constant from begin to end
Traversing way	Shaft arange take-up,no damge in product process,the size could establishment by yourself
Pay-off type	Linear guidways+slide weight hommer type/mechanicallever+slide moveing,with the tension test
Shaft of take-up	φ300-φ500general shaft
Shaft of pay-off	φ400-φ630general shaft
Machine size (mm)	(L)1450x(W)1400x(H)1900
Weight	1300KG

 

High speed horizontal type cantilever single twisting machine

Uses widely: Suitable for high frequency cable, data cable, pair twist of electrical core wire and many stranded to twist.
High output: High speed of rotation, the production efficiency is two times than vertical.
Tension is steady: Wrapping and take up tension keep constant from start to end.
Lay accurate: Machinery lay, the lay can be keep constant when acceleration-deceleration and on normal work.
Good traversing: The take-up and pay-off adopts axis arrange, the size could establishment by yourself.
High quality: Production the HDMI, DP and so on, rate of pass100%

 

Type	YK-500mm High speed horizontal type cantilever single twisting machine
Purpose	HDMI、DP、USB、CAT-7 and so on high frequnce cable、data cable、electical core wire and many kinds of pair twisting
Core specification	AWG32-AWG20
Twisting out dia.	φ4.0mm
Lay scope	15-60mm
Rotation speed	MAX1000rpm
Power	Main engine:5HP/Pay-off:1/2HP
Core tension	Linear guldways+Slide weight hommer type/Mechanical lever+Side moveing,with the tension test
Taping tension	Constant tension elect romagnetism brake wheel/Automatic tension trace instrument,Taping tension keep constant from begin to end
Take-up tension	Electrcle tension,by itself,Take-up tension keep constant from start to end
Traversing style	Shaft arange take-up,no damge in product process,the size could be establishment by yourself
Brake of machine	The main shaft of cantilever:Dish type brake/Take-up volume:Electromagnetism brake
Pay-off type	Three power pay-off,adjust the speed by motor drievers,controled with main machine by linkage,and establishment the protection
Shaft of take-up	φ300-φ500general shaft
Shaft of pay-off	φ400-φ500general shaft
Machine size (mm )	(L)4250x(W)1200x(H)1500
Weight